Srpski

"FULL"
Programer for satellite cards

Supports:
TitaniumCard (AVR RISC)
FunCard (ATMEL)
Silverwafer (Piccard2, DS9)
Goldwafer (Piccard1)
JupiterCard (ATMEL2343)
SMDcard (PIC16F84)
Multimac2 card (PIC16F84A+24C16)
GSM SIMcard (read only)
Original DVB (SECA/Irdeto/Viaccess)
(microcontrollers and serial eeproms)

 

    programmer + DB9 cable for COM port + special power supply 15V DC + manual + software
80 EUR

buttons "UP" & "Down" changes the working mode

display

mode
P PICcard programming (Goldwafer, Silver DS9, SMD)
3 Eeprom read/write using phoenix @ 3.57Mhz
A Atmel-card programming (FUNcard, Jupitercard)
6 Eeprom read/write using phoenix @ 6.00MHz


"automatic mode switching"
(short description: initail mode is "P", than after the PC programms the "loader" into the card, programmer switches the working mode into "3" ready to take a "write" procedure for eeprom, after successful operation, the mode is switched back to "PIC", ready to take the programming of "Pic.hex" - software for card. "automatic mode" is enabled after keeping one button pressed for a while, than the display is blinking to indicate the "auto-mode")

display

mode
P (blinking) PICcard programming (Goldwafer, Silver DS9, SMD)
3 (blinking) Eeprom read/write using phoenix @ 3.57Mhz

 

Software for Programmer:
ICprog v1.04 ("Smartcard wizard" is working with "auto mode switching" feature)
ICprog driver for Win2000
PicBinEdit
Winphoenix v1.06
PonyProg v1.17c
and so many other programs that can be founded on the net.


Loaders for wafer cards:
LoaderPic.HEX for Goldwafer, SMDcard
LoaderPic876.HEX for Silverwafer (DS9)
LoaderAtmel.HEX for FunCard (Atmel)

 

User manual for programmer:
User Manual

 

Contact:

tel: + 381 63 8160-178 Milan
e-mail: SEND

More details about programmer:

Also supporting:

I²C EEPROMs 24xx
(24C01 24C02 24C04 24C08 24C16 24C32 24C64/65 24C128 24C256 24C512)

Microchip PIC microcontrollers
- PIC12C508 PIC12C509 (programmer v2.4 and higher)
- PIC16C554 PIC16C556 PIC16C558 PIC16X83 PIC16C84 PIC16F84 PIC16F628 PIC16F876)
all microcontrollers PIN-compatable with those 16F84 and 12C508

MAIN FEATURES:
This device is "4 in one". It has PHOENIX interface for comunication between smartcard and PC under two speed 3.57MHz or 6.00 MHz . Smartcard connector is used for cards which are made under ISO7816 card standard. The device use serial port on PC (9-pin COM port) connected via standard DB-9 cable attached to 15V DC power supply. Also, the device supports the programming of AVR (AT90S....) microcontrolers on the card (i.e. FunCard) without desoldering it. Programming of serial eeproms can be done using many of softwares available on the Internet. Power supply (15V DC) is also included in a package and it is very stabillized and it can reject the noise from main power, as well.


"HALF"
Programmer for satellite cards

Supports PIC-based cards:
Silverwafer (DS9) & Goldwafer (SMD & PIC) & GSM SIMcard & TitaniumCard



programmer + DB9 cable for COM port + user manual + software =
40 EUR

Software for Programmer:
ICprog v1.04
PicBinEdit
Winphoenix v1.06

User manual for programmer:
Programmer ver:2.0L

 

Contact:

tel: + 381 63 8160-178 Milan
e-mail: SEND

"FUN"
Programator only for FUNcards

Programms
(ATMEL-based cards)
FUNwafer & FUNcard



programmerr + LPT cable + manual + software =
30 EUR

Software for Programmer:
FUNprom v2.47
(leatest version on www.funcard.net)

 

Manual for programmer:
FunCard Programmer v2.0

 

Contact:

tel: + 381 63 8160-178 Milan
e-mail: SEND